常州導熱油泵?常州市武研熱油泵有限公司?安裝順序：待混凝土干固后，檢查底座和地腳螺栓是否有不良或松動等現象，檢查合格后應擰緊地腳螺栓并重新檢查常州導熱油泵的水平度。校正泵軸和電機軸的同軸度，用驗平尺檢驗時在聯軸器外圓上的圓跳動不能超過0.1毫米，兩個聯軸器平面間的間隙要保證在2-3毫米之間，通過驗平尺相差90°對聯軸器進行校驗時另一方向的圓跳動也不得超過0.1毫米，調節時一般相對于泵來調節電機，可用平板墊的墊入方法來調整聯軸器的同軸度。Installation order: do to be solid concrete, check the base and anchor bolt whether there is adverse to loosening, after passing the examination should tighten the anchor bolts and re check the pump level. Calibrated pump shaft and motor shaft coaxial and inspection test ruler in coupling outer circle of the circular runout cannot exceed 0.1 mm, two plane of couplings between the gap to ensure between 2-3 mm, through inspection ruler difference 90 DEG couplet axis device to check another direction round jump move nor more than 0.1 mm, adjust the general with respect to the pump to adjust the motor, available flat pad pad method to adjust the coupling of coaxial degree.
常州市武研熱油泵有限公司
地 址：常州市武進區橫林鎮橫玉路247號
銷 售：,
售 后：
傳 真：
手 機：
: 876363125
郵 箱：WRY@vip.163.com
常州熱油泵：www.wry006。。ｃｏｍ
WRY熱油泵：www.wry002。。ｃｏｍ
熱油泵配件：www.wry008。。ｃｏｍ
離心式熱油泵：www.wry003。。ｃｏｍ
友情鏈接：耐腐蝕化工泵 www.wyryb。。ｃｏｍ
鍋爐輔機：www.whboiler。。ｃｏｍ
刮板出渣機：www.cz-boiler。。ｎｅｔ
主動/被動爐排片：www.glfj。。ｎｅｔ
提升式上煤機：www.wh-boiler。。ｃｏｍ
武研導熱油泵：http://wrypump.cn.alibaba.com
鍋爐輔機配件：http://glboiler.cn.alibaba.com
2015.6.2張
