 |
上海突越機械設備有限公司
主營產品： 諾冠Norgren、海隆Herion、寶碩Buschjost |
會員1.png)
|
上海突越機械設備有限公司
主營產品： 諾冠Norgren、海隆Herion、寶碩Buschjost |
| 參考價 | 面議 |
聯系方式：吳年平查看聯系方式
更新時間：2015-12-09 11:31:18瀏覽次數：391
聯系我們時請說明是環保在線上看到的信息，謝謝!
上海突越機械設備有限公司是一家專業經銷英國Norgren氣動元件，是經國家相關部門批準注冊的企業。公司主營諾冠Norgren、海隆Herion、寶碩Buschjost氣動元件。
公司本著“客戶*，誠信*”的原則，與多家企業建立了*的合作關系。熱誠歡迎各界朋友前來參觀、考察、洽談業務。
以下是公司部分產品常備庫存，貨期短，咨詢
VP5005BJ411HS1
VP5006BJ411H00
B73G-4GK-QT1-RMN
F72G2ANAE3
B72G-3GK-AL1-RMN
B72G-2GK-AL3-RMN
11-009-073
0880300.0000.000.00
B73G3GKQT3RMN
B74G-3GK-QP3-RMN
B72G-2GK-QT3-RMG
4466-51RF
F73G-2GN-AT3
F74C4GDQP0
F73G-4AN-AP1
B68G-NNK-AR2-RLN
L64C-NNP-EDN
L73M4GPEDN
L74M-6GP-EPN
B68E-NAK-AU1-RLN
L68M-NNP-QUN
T64E-4AB-P1N
F73G-4AN-QT1
Y64A-4GA-N1N
160290028
18-013-857
VP5005BJ411HS1
B64G-NNK-AD3-RMN
L64M-NNP-EDN
Y64A-4GA-N2NADJUSTMENT
1.Before applying inlet pressure to filter/regulator, turn
adjustment (1 or 7) counterclockwise to remove all force
on regulating spring (12).
2.Apply inlet pressure, then turn adjustment (1 or 7)
clockwise to increase and counterclockwise to decrease
pressure setting.
3.Always approach the desired pressure from a lower
pressure. When reducing from a higher to a lower
setting, first reduce to some pressure less than that
desired, then bring up to the desired pressure.
NOTE
With non-relieving filter/regulators, make pressure
reductions with some air flow in the system. If
made under no flow (dead-end) conditions, the
filter/regulator will trap the over-pressure in the
downstream line.
4.KNOB ADJUSTMENT. Push knob down to lock pressure
setting. Pull knob up to release. Install tamper resistant
cover (see Replacement Items ) to make setting tamper
resistant.norgren過濾調壓閥
5.T-BAR ADJUSTMENT. Tighten lock nut (8) to lock
pressure setting.
SERVICING
1.Open manual drain to expel accumulated liquids. Keep
liquids below baffle (49).
2.Clean or replace filter element when dirty.
DISASSEMBLY
1.Filter/regulator can be disassembled without removal
from air line.
2.Shut off inlet pressure. Reduce pressure in inlet and
outlet lines to zero.
3.Turn adjustment (1 or 7) fully counterclockwise.
4.Remove bowl - push into body and turn
counterclockwise.
5.Disassemble in general accordance with the item
numbers on exploded view. Do not remove the drains
unless replacement is necessary. Remove and replace
drains only if they malfunction.
CLEANINGnorgren過濾調壓閥
1.Clean plastic bowl (25, 35) with warm water only. Clean
other parts with warm water and soap.
2.Rinse and dry parts. Blow out internal passages in body
(16) with clean, dry compressed air. Blow air through
filter element (50) from inside to outside to remove
surface contaminants.
3.Inspect parts. Replace those found to be damaged.
Replace plastic bowl with a metal bowl if plastic bowl
shows signs of cracking or cloudiness.
ASSEMBLY
1.Lubricate the following items with o-ring grease.
4 (Thrust washer) - outer circumference and both sides.
5, 7 (Adjusting screw) - threads and tip.
18, 28, 37 (Manual drain body) - the portion of the
body that contacts the bowl, and the hole that
accommodates the stem of drain valve (19, 29, 38).
53 (Valve) - stem.
26, 34, 47, 54 (O-rings)
2.Assemble the unit as shown on the exploded view. Push
bowl, or bowl with guard, into body and turn fully
clockwise.
3.Torque Table
Item Torque in Nm (Inch-Pounds)
2, 9 (Screw) 2,3 to 3,4 (20 to 30)
22, 32, 41 (Nut) 2,3 to 2,8 (20 to 25)
43 (Screw) 1,7 to 3,4 (15 to 30)
49 (Baffle), 51 (Louver) 1,1 to 2,2 (10 to 20)
