使用說明書

Operation guide book

Preface

Correct operation, serious maintenance and observing safety regulation are of necessity for raising operation efficiency, prolonging service life and ensuring safety. To avoid accident and raise production efficiency, the operator should know the operation of filter press well and be familiar with its’ structure and filtration principle.

Now we manufacture box filter, plate-frame filter and diaphragm filter press and box filter press is our main product. So this Manual is based on box type. The working principle of plate-frame one is similar with box type, so the Manual is also used for plate-frame one as a reference.

前言

正確安裝使用壓濾機，認真維護、保養和嚴格遵守安全操作規程是提高設備使用效率、延長設備使用壽命、保證安全生產的必要條件。因此操作者應熟練掌握壓濾機的正確操作方法，還應熟悉壓濾機的基本結構和過濾基本原理，才能提高生產效率及避免不必要的設備事故或損壞。

目前我公司生產的壓濾機主要有廂式、板框式和隔膜壓榨式等系列，廂式壓濾機與板框式壓濾機相比有許多*性。在實際生產中以廂式壓濾機為主。本說明書也是根據廂式壓濾機操作特點而編寫的，但板框式壓濾機與廂式壓濾機工作原理基本相似，所以也能參考。

Briefing

The principle of filter press is that the pressure difference on two side of filter cloth push the liquid in material penetrating the cloth and exiting the filter press and the material remains in filter as filter cake. Filter press is widely used in chemical, pharmacy, ceramic, sugar, dye, cement, silicate and other industry.

                         概述

壓濾機是利用濾布兩邊的壓力差，迫使物料中的絕大部分水份透過濾布，流出機體外，而物料被阻隔在濾室內形成濾餅，以達到過濾的目的。目前，壓濾機已廣泛用于化工、制藥、冶金、陶瓷、制糖、顏料、染料、水泥、硅酸鹽等工業以及市政與工業污泥脫水等方面。

 Description of type

壓濾機型號說明

                    Installation

1. Filter press shall be installed on cement foundation horizontally and secondary grouting is necessary.(The pedestal of thrust plate shall be fixed with bolts and the pedestal of oil cylinder shall not be fixed).

To convenient discharging, one meter free space around filter should be arranged. Filter shall avoid rain and direct sunshine.

2. Connecting power. The motor shall rotate clockwise.

3. Open air cleaner and add hydraulic oil to a level lower than motor

4. Mount return pipe, stop valve and pressure gauge.

5. Mount filter cloth.

6. Final check.

安裝

1.壓濾機應水平安裝于混凝土基礎結構上，安裝的基礎應采用二次灌漿。（注意在止推板下方的支架處用螺栓固定，油缸下方支架不需固定，不要包水泥）以保證壓濾機在受壓情況下的自由度?？紤]到壓濾機在卸料時便于操作，機架周圍應留一米左右的空間。

2.接好電源，電機需順時針旋轉。

3. 打開空氣濾清器注入液壓油，油面高度與電機蓋板水平稍低一些。

4. 進料管處應安裝回流管、截止閥和壓力表。

5. 裝上濾布。

6．zui后的檢查工作。

Piping installation and operation sequence

1. See sketch for piping installation.

2.  operation sequence

(1) press plate and frame

(2) open charging valve, shut return valve

(3) start charging pump

(4) control the filtration pressure by adjusting return valve to required pressure , but no higher than 0.4Mpa

 (5) adjust charging pressure by control return valve. When filter liquid’s flow rate becomes rather low, shut down charging pump and release the filter plate to unload filter cake.

 (6) If the filter cake is not dry enough, press the filter plate and filtrate again.

工藝管線安裝和操作程序

1.工藝管線安裝示意圖

2．操作程序

（1）壓緊板框；

（2）打開進料閥，關閉回流閥；

（3）啟動進料泵；

（4）觀察壓力表在過濾過程中的壓力，根據實際情況控制過濾壓力，打開回流閥，使壓力控制在0.4Mpa以下;

（5）用回流閥調節進料壓力,直至過濾的出液量很小,即可關閉進料泵,若不需要洗滌,既可打開濾板,卸料;

（6）如打開濾板,感到濾餅不夠干,可繼續合上壓緊板，再度過濾；

Precaution

1. Filter press shall be operated with the required filter plates installed by specified sequence .

2. The pressure of oil cylinder shall not exceed rated value.

3. The Valves shall be opened in a sequence specified in Operation Manual.

4. The temperature of filter material shall not higher than 80℃.

5. when moving filter plate, care must be taken to avoid collision and protect the sealing surface and handles.

6. After unloading filter cake, filter plate and filter cloth shall be cleaned and no residual shall be left on the sealing surface and passage.

7. Right filter cloth shall be used to meet filtration requirement.

8. Filter cloth shall be checked periodically.

9. The hydraulic elements of oil box, oil cylinder, oil pump and return valve shall be no-load operated periodically and cleaned .

10.Normally the oil shall be changed after first operation and then every six month. The oil shall be filtrated to 20um.

11. For lifting filter press, see sketch  .

注意事項

1．必須按次序和規定的數量放置濾板。

2.油缸的壓力不得超過額定值。

3.閥門必須按操作程序啟用。

4.過濾的濾漿溫度必須控制在不高于80℃。

5.移動濾板時，用力應均勻適當，不得碰撞摔打，以免損壞密封面及手柄。

6.卸餅后的濾板和濾布必須沖洗干凈，絕不允許有殘渣貼在密封面或孔道上。

7.濾布選擇一定要符合濾漿的過濾要求。

8.濾布在需定期檢查。

9.油箱、油缸、油泵和溢流閥等液壓元件需定期進行空載運行，循環清洗干凈。    

10.在一般工作環境下*次使用的壓濾機應在一個月內換油。工作油的過濾精度為20um，工作油的更換周期為6個月。

11、機組吊運參看草圖。

                 Safety Operation

1. Preparation before commissioning

  1) Check the tightness of bolts, completeness of parts, correctness of oil path and electric circuit.

  2) Check if the rotating parts move smoothly and agilely.

  3) Filter cloth shall be mounted on filter plate correctly.

2. Safety Regulation

  1) The one who is not familiar with filter press is not allowed to operate.

  2) If serious leakage and abnormal condition are found, the operation shall be stopped immediay, find out the cause and fixed it.

  3) While operating, no maintenance shall be carried out.

  4) The operation pressure shall not exceed the specified one.             

安全操作

1、調試前的準備工作：

1）檢查各緊固件是否緊固，零部件是否齊全，油路、電路安裝是否正確。

2）檢查各傳動部件是否靈活，高低壓油管連接是否正確無誤。

3）濾布正確的安裝在濾板上。

2、安全操作規程：

1）不了解機器結構性能和操作規程者，不應擅自開動機器。

2）發現機器有嚴重漏油或工作中發生不正常現象，應立即停止檢查分析原因并排除故障。

• 機器在工作過程中，不得檢修或調整設備部件。

4)不許在超過使用壓力下工作。