電腦全自動恒應力壓力試驗機是**檢測儀器，用于測定磚、石、砼等建筑材料的抗壓強度。使用前務必仔細閱讀說明書。并由**實驗人員操作，以避免操作不當引起的傷害。如需了解更多資料請與我公司客服人員聯系。
Full-automatic concrete pressure testing machine is a testing instrument used to determine the compressive strength of building materials such as brick, stone, and concrete. Be sure to read the instructions carefully before use. It is operated by ** experimental personnel to avoid injury caused by improper operation. For more information, please contact our customer service staff.
電腦全自動恒應力壓力試驗機符合**標準《普通混凝土力學性能實驗方法標準》，自動控制加載速度，并具有加荷速度顯示窗口、峰值保持、過載保護功能，由上海榮計達儀器科技有限公司提供，設備質保期一年，一年內產品如有質量問題，供方負責免費維修。如果因操作不當或者人為損壞，我公司亦應提供維修、更換服務，由此產生的費用我公司會酌情收取。
Fully-automatic concrete pressure testing machine conforms to the ** standard "Standard for Experimental Methods of Mechanical Performance of Common Concrete", automatically controls the loading speed, and has a loading speed display window, peak hold, and overload protection functions. Provided by Shanghai Rongjida Instrument Technology Co., Ltd. The equipment warranty period is one year. If the product has quality problems within one year, the supplier is responsible for free maintenance. If due to improper operation or man-made damage, our company should also provide repair and replacement services, and the costs incurred by our company will be charged as appropriate.
電腦全自動恒應力壓力試驗機為手動調節上下壓板間距，液壓加荷有微機顯示計算儲存功能打印數據報告。大大降低了故障率。采用進口比例閥，穩定性高，加荷速度平穩。
The automatic concrete pressure testing machine is to manually adjust the distance between the upper and lower pressure plates, and the hydraulic loading has a microcomputer display calculation and storage function to print data reports. Greatly reduced the failure rate. Imported proportional valve, high stability and stable loading speed.
電腦全自動恒應力壓力試驗機技術參數:
★大載荷：2000kN
★示值準確度：一級
★分辨值：0.1kN
★承壓板間大距離：320mm
★上下壓力板規格：250×220mm
★活塞直徑*大行程：直徑250×30mm
★電機功率：0.75KW
★輸入電壓： 380V
★外型尺寸： 880×480×1400mm
★凈重： 850kg
Technical parameters of automatic concrete pressure testing machine
★ Large load: 2000kN
★ Accuracy of displayed value: first level
★ Resolution: 0.1kN
★ Large distance between pressure plates: 320mm
★ Upper and lower pressure plate specifications: 250 × 220mm
★ Piston diameter * large stroke: 250 × 30mm diameter
★ Motor power: 0.75KW
★ Input voltage: 380V
★ External dimensions: 880 × 480 × 1400mm
★ Net weight: 850kg
電腦全自動恒應力壓力試驗機使用與操作注意事項:
★ 使用前應先檢查油箱內的油液是否充足，可察看右側面油標，如不足，則應打開后箱板向油箱內添加之，至液面在油標處為宜。
★檢查各油灌接頭和緊固件是否松動，如有松動則擰緊之。檢查防塵罩應完整無損。檢查電氣接地、保險熔絲等安全防護措施是否有效。
★一次使用時，應先將回油閥打開，關閉回油閥，接通電源，按下啟動按鈕，油泵開始工作，然后關閉回油閥，徐徐打開送不油閥，活塞上升一段距離，有無卡住等現象。如有，則應卸荷、停機檢查，并排除之。打開回油閥，活塞則下降到原位。
★ 將試件表面擦拭干凈，檢查外觀有無明顯缺陷，如有能影響試驗數值者，須更換無損試件。
★按試件下壓板定位線框放在下壓板正中，并按試件大小，轉動手輪和絲杠，調節上壓板至適當位置。
★接通測控系統電源(開關在測控箱背后)，按操作步驟進行清零以及時鐘修改等各有關數據的輸入。
★按下啟動按鈕，關閉回油閥，調控送油閥，按需要速率平穩進行加荷試驗，及至試件被壓碎，負荷下降。隨即打開回油閥，使油液迅速流回油箱。
★試驗結束時，按面板上“打印"鍵。打印機即可打印輸出該次的試驗報告。
★ 操作時，下壓板上升高度不得超過4cm(或立柱上標志線)，以免發生意外。
★ 操作中禁止手等人體任何部分置于上下壓板之間，并注意試件在破碎時碎片崩出傷人。
★試后隨即清除破碎試塊，以待下次試驗。當不再做試驗時，要打開回油閥，關閉送油閥，切斷電源。
Precautions for use and operation of automatic concrete pressure testing machine
★ Before use, check whether the oil in the fuel tank is sufficient. You can check the oil level on the right side. If it is insufficient, you should open the rear tank plate and add it to the fuel tank.
★ Check whether the oil fittings and fasteners are loose, and tighten them if they are loose. Check that the dust cover is intact. Check whether the safety protection measures such as electrical grounding and fuse are effective.
★ When used once, the oil return valve should be opened, closed, and the power should be turned on. Press the start button to start the oil pump, then close the oil return valve, slowly open the oil delivery valve, and the piston rises a distance. No jams and so on. If there is, it should be unloaded, stopped and checked, and excluded. Open the oil return valve and the piston descends to its original position.
★ Wipe the surface of the test piece clean and check for obvious defects in the appearance. If it can affect the test value, replace the non-destructive test piece.
★ Position the wire frame of the lower plate of the test piece in the middle of the lower plate. According to the size of the test piece, turn the handwheel and the screw to adjust the upper plate to the proper position.
★ Turn on the power of the measurement and control system (the switch is on the back of the measurement and control box), and follow the operation steps to clear the data and modify the clock.
★ Press the start button, close the oil return valve, regulate the oil delivery valve, and perform the loading test smoothly at the required rate until the test piece is crushed and the load is reduced. The oil return valve is then opened, allowing the oil to quickly flow back to the tank.
★ At the end of the test, press the "Print" key on the panel. The printer can print out the test report.
★ During operation, the height of the lower platen must not exceed 4cm (or the marking line on the column) to avoid accidents.
★ It is forbidden to place any part of the human body, such as hands, between the upper and lower pressure plates during operation, and pay attention to the fragmentation of the test piece when it is broken to hurt people.
★ After the test, the broken test block is cleared for the next test. When no longer doing the test, open the oil return valve, close the oil supply valve, and cut off the power.
