進口蒸汽氣動調節閥_進口蒸汽調節閥_進口氣動調節閥
美國歐可進口蒸汽氣動調節閥就是以壓縮空氣為動力源，以氣缸為執行器，并借助于電氣閥門定位開關、轉換器電磁閥、保位閥等附件去驅動閥門，實現開關量或比例式調節、被評為歐美zui認可的閥門之一 。
進口蒸汽氣動調節閥標準規范:
公稱通徑：DN20～600
公稱壓力：ANSI 150LB～1500LB
連接形式：法蘭、焊接
適用溫度：－46～380℃
進口蒸汽氣動調節閥的日常維護：
當調節閥采用石墨一石棉為填料時，大約三個月應在填料上添加一次潤滑油，以保證調節閥靈活好用。如發現填料壓帽壓得很低，則應補充填料，如發現聚四氟乙燥填料硬化，則應及時更換；應在巡回檢查中注意調節閥的運行情況，檢查閥位指示器和調節器輸出是否吻合；對有定位器的調節閥要經常檢查氣源，發現問題及時處理；應經常保持調節閥的衛生以及各部件完整好用。
產地：美國
產品品牌：美國歐可<OKE>
美國OKE制造標準：德標、國標、美標。
The United States of America Europe can be imported steam regulating valve is driven by compressed air source, to the cylinder as the actuator, and with the aid of electrical valve position switch, the electromagnetic valve, and a converter valve and other accessories to drive the valve, realize the switch quantity or proportional adjustment, was named one of Europe's most recognized valve.
Steam regulating valve standard:
Nominal size: DN20~ 600
Nominal pressure: ANSI150LB ~ 1500LB
Connection: flange, welding
Application of temperature:46~ 380 C
Steam regulating valve maintenance:
When the regulating valve adopts graphite asbestos packing, approximay three months in the filler added a lubricating oil, to ensure that the regulating valve is flexible and easy to use. If the packing gland pressure too low, should complement fillers, such as found in Teflon B dry packing hardening, should be timely replacement; should be in the inspection tour in the operation of control valve, check valve position indicator and the regulator output is consistent; the positioner valve to always check the source, found problem timely treatment should be maintained; valve and components complete good health.
Origin: the United States of America
Brand: American Ou < OKE >
The United States of America OKE manufacturing standards: GB, American Standard, German standard.
進口氣動蒸汽調節閥是用于蒸汽管道系統的氣動調節閥，對蒸汽的壓力，流量，溫度進行調節，以滿足工礦要求。
進口氣動蒸汽調節閥的閥體
型 式：直通單座鑄造球型閥
公稱通徑：10、15、20、25、32、40、50、65、80、100、125、150、200mm
公稱壓力：PN1.6、4.0、6.4MPa
法蘭標準：ANSI B16.5 ，JB/T79.1-94、79.2-94等
材 料：鑄鋼（ZG230-450）、鑄不銹鋼（ZG1Cr18Ni9Ti、ZG1Cr18Ni12Mo2Ti）、鉻鉬鋼等
上 閥 蓋：標準型-17～+230℃、散熱型+230～+450℃、低溫型-60～-196℃、波紋管密封-40～+350℃
壓蓋型式：螺栓壓緊式
填 料：V型聚四氟乙烯填料、含浸聚四氟乙烯石棉填料、石棉紡織填料、石墨填料
結構形式：標準型、散熱型、低溫型、波紋管密封型、保溫夾套型和襯氟型
進口蒸汽氣動調節閥的日常維護：
當調節閥采用石墨一石棉為填料時，大約三個月應在填料上添加一次潤滑油，以保證調節閥靈活好用。如發現填料壓帽壓得很低，則應補充填料，如發現聚四氟乙燥填料硬化，則應及時更換；應在巡回檢查中注意調節閥的運行情況，檢查閥位指示器和調節器輸出是否吻合；對有定位器的調節閥要經常檢查氣源，發現問題及時處理；應經常保持調節閥的衛生以及各部件完整好用。
產地：美國
產品品牌：美國歐可<OKE>
美國OKE制造標準：德標、國標、美標。
本產品可廣泛應用在：給排水、工業、蒸汽、油田、電站等流體管道。
會員1.png)
